2 posts Page 1 of 1
Postby anyway » Mon Apr 16, 2018 6:57 am
A fan cannot perform as designed if the air flow surfaces are distorted by contaminants. Even in large fans Derek Stepan USA Jersey , a sixteenth of an inch of build up can reduce performance. Centrifugal fans will move some air even when running backwards. While some types would use so much horsepower they would trip circuit breakers, other design s could run for years without being detected. Fan components may be out of position due to routine cleaning or painting or the wheel could have shifted during shipment. For backward inclined fans, the relation of wheel to inlet cone is very critical. Even a quarter of an inch can have a major impact. The fan’s installation and maintenance literature shows the proper positioning of the wheel to the inlet cone.

Industrial processes and plant ventilation systems often need more air than originally designed. Increased production requirements, process changes, and facility renovations are a few of the major reasons. Additionally David Backes USA Jersey , the lack of adequate maintenance over time can negatively impact system airflows. This article discusses several procedures that can increase airflow. Often airflow can be increased by adhering to proper fan maintenance procedures as outlined in fan installation and maintenance literature.

The design and maintenance of the system plays a large role in achieving the overall desired performance. Visual inspections often reveal some easily rectified problems that can significantly impair performance. If the system has not been properly maintained, clogged filters or obstructed coils will reduce airflow. The greater the obstruction, the greater the loss in airflow. Any leaks in the ductwork will contribute to reduced perfo rmance, especially leaks around plenum bulkheads that can lead to recirculation of air. Worn flexible connectors are a common source of leaks and should be inspected regularly. If the damper linkage is out of adjustment, the damper may not be opening completely Cory Schneider USA Jersey , thereby reducing performance. If inlet dampers are used, make sure they are installed so that the air is pre-spun in the same direction as wheel rotation. For all dampers, make sure there is sufficient clearance for the blades to open and close completely without hitting the ductwork or other system components. Last, for systems with either pneumatic or electric controls, make sure damper actuators are operating properly. Sharp changes in the direction of airflow at either the fan inlet or outlet will disrupt the flow through the fan and impair performance. If it is impossible to straighten the ductwork entering and leaving the fan Brian Rafalski USA Jersey , the use of inlet boxes and turning vanes can minimize performance losses.

One of the easiest solutions to low airflow problems is speeding up the fan. While airflow is increased by speeding up the fan, so too are static pressure, noise, and power requirements. Therefore, while increasing the fan’s speed is an easy procedure with low first cost Brandon Dubinsky USA Jersey , the additional operating expense over time makes it the most costly solution. When increasing fan speed, it is necessary to check the maximum safe speed of the fan and make sure the motor is capable of the horsepower required to run the fan at the new speed. But never run a fan beyond its maximum safe speed.

On a first-cost basis, adding or replacing fan equipment is the most costly alternative. However, on a life-cycle-cost basis, considering operating and maintenance expense Blake Wheeler USA Jersey , it can be the least expensive, as compared to increasing the speed of an existing fan. Sometimes a second fan may be added, either in series or parallel with the original, although it may be more cost effective to simply upgrade the system with a new fan capable of the required airflow and pressure. Adding another fan in series will increase the airflow because of the additional pressure. The operating point of the new system moves further outup the system curve. Where duct size is adequate to handle the desired amount of air but the existing fan doesn’t provide sufficient pressure, a second fan in series may be the best solution. However Ben Bishop USA Jersey , make sure the ductwork can handle the increase in pressure. Adding another fan in parallel with the first will increase airflow due to the combined capacities. Because capacities are being combined instead of pressures, a greater increase in airflow will result for a given system. However, system pressures will also increase and caution is required to avoid the unstable operating area of the combined fan system.

When more air is required it is important to investigate the system on a step-by-step basis, considering the least expensive possibilities first. For existing systems that seem to have lost performance, fan and system maintenance is the place to start. Often Zach Parise Jersey , simply improving the efficiency of existing components will suffice. For systems that require greater airflow and or pressure, increased fan speed is generally the first alternative. However, when large increases in performance are required, there may be no alternative but to purchase a larger fan.

For additional information please refer to http:www.industrialpressureblowerblower

Oleg Tchetchel
Industrial Air Systems Engineer
blower@industrialpressureblower
Industrial Pressure Blower Co.
http:www.industrialpressureblowerahu
http:www.industrialpressureblowerfan Are you a senior aged individual searching for a date? There are individuals of all ages who're turning to the internet for assist with discovering a date. Finding a date at your age, simply because you are a senior citizen Tim Thomas Jersey , does not have to be inconceivable, or even a problem for that matter. Finding a date as a senior is actually very simple when you think about how many completely different senior dating service choices are out there.

Most senior people who are in search of a date will think about somethin.
Postby vanchacha » Wed Jul 18, 2018 8:58 am
aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721
aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721
aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721
aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721
aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721
aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721
aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721
aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721
aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721
aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721
aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721aul4721
aul4721aul4721
2 posts Page 1 of 1

Login

Who is online

Users browsing this forum: Google [Bot] and 6 guests

cron